Neptune Electric

New energy vehicle

主页 > ENGLISH > PRODUCTS > New energy vehicle >

NVR6V-100B download

1. CCC and RoHS compliant；

2. Contacts sealed in ceramic capsules and inert gas；

3. Contacts protected against contamination. e.g oxidation and corrosion;

4. Magnet arc blowout;

5. Up to 900VDC Cutoff;

6. Compact and lightweight;

一、 Product Names and Type Rules

NVR6V

100

800

( )

Product Type

NVR6V： Ceramic

Load Current

100：100A

Series Indicator

B：B Series

Load Voltage

800：800V

Coil Voltage

12：12VDC

Contact Form

H： 1 Form A of Main Contact

Coil Terminal Form

C：Connector

Load Terminal Form

5：Internal Thread

Special Code

Customer's special requirements

二、 Coil Data
@23 ℃

Rated Voltage Vd.c.	Coil Type	Operate Voltage Vd.c.	Release Voltage Vd.c.	Coil Resistance Ω(@23℃)	Coil Power (Approx.) W
12	Single Coil	≤9	≥1.2	24×(1±7%)	6

三、Contact Data

Main Contact	Contact Form	1 Form A
	Contact Material	Copper Alloy
	Contact Resistance	≤0.4mΩ (@100A)
	Contact Rating Current	100A(@35mm² Copper bar)
	Max. Breaking Current	1000A/450Vd.c.(1 op)
	Max. Switching Voltage	800Vd.c.
	Min. Applicable Load	6Vd.c./1A
	Operate Time	≤30ms
	Bounce Time	≤5ms
	Release Time	≤10ms
	Current Endurance	100A Cont. 150A 2h 200A 10min 400A 30s 600A 10s 900A 4s

Current Endurance Curve
Notes:
1)
The ambient temperature is 85℃, and the cross-sectional area of the copper bar is ≥35mm². Supply rated voltage to coil;
2)
The upper limit of the function temperature is 130℃, which is suitable for long-time working; and the upper limit of the safe temperature is 180℃, which is suitable for short-time working; If the temperature exceeds 180℃,the contactor may fail;
3)
The contactor’s contacts may be repelled when the current is greater than 2000A, if the fuse does not blow
in time, the contactor may catch fire or explode.

四、 Endurance

Electrical Life(Resistivity)	Making:	14.5Vd.c./100A 5×10⁴(ops) 450Vd.c./100A 1×10⁴(ops)
Electrical Life(Resistivity)	Breaking:	800Vd.c./100A 1500(ops) 450Vd.c./100A 4000(ops)
Mechanical Life	200,000(ops)

Notes:
1)
Electrical Life tests are conducted in room temperature. Supply rated voltage to coil. On/off ratio is 0.6s:5.4s;
2)
Mechanical Life tests are conducted in room temperature. Supply rated voltage to coil. On/off ratio is 0.5s:0.5s.
五、Other Properties

Insulation Resistance	Between Open Contacts	Before Test: ≥1000MΩ(@1000Vd.c.) After Test: ≥50MΩ (@1000Vd.c.)
	Between Closed Contact and Coil	Before Test: ≥1000MΩ(@1000Vd.c.) After Test: ≥50MΩ(@1000Vd.c.)
Dielectric Strength	Between Open Contacts (Leak Current≤1 mA)	Before Test: ≥3000Va.c.,(50/60 Hz, 1min) After Test: ≥2250Va.c.,(50/60 Hz, 1min)
	Between Closed Contact and Coil (Leak Current≤1 mA)	Before Test: ≥2500Va.c.,(50/60 Hz, 1min) After Test: ≥1875Va.c.,(50/60 Hz, 1min)
Mechanical Shock-Destructive		50G
Mechanical Shock-Functional		20G
Vibration		10-500Hz，5G

六、Configuration
1. Product Model：NVR6V-100B/800-xx-HC5
1.1. Outline Dimensions

1.2. Wiring Diagram

No polarity on the load and coil

1.3. Product Weight

Specification	Weight
12V	Approx.260g
24V	Approx.260g

Notes：
1) All unspecified tolerance please refer to the following table:

Dimension(mm)	＜10	10~50	＞50
Tolerance(mm)	±0.3	±0.5	±0.8

2) Recommended connector:
Yazaki 7283-1020
THB 0435317
3) The default product is shipped without connector harness,screws,washers,spring washers and other installation accessories.

七、Application Condition

Application Condition	Standards Test Condition	Operating Condition	Storage Condition
Temperature	23 ℃±5 ℃	-40℃～+85℃	-40℃～+85℃
Humidity	25%～75%RH	5%～85%RH	5%～85%RH
Altitude	≤2000m	≤4000m	≤4000m
Direction	Same as Installation Direction	Vertical	Forward Packing

Notes：
1)
Since the fixed contact of this product is made of pure copper, if the storage time is longer, the oxidation degree of the contact surface should be checked before use. If oxidation discoloration has occurred, the surface of the contact should be polished to remove the oxide layer before use.The storage environment should avoid condensation and icing.
2)
If the storage time exceeds 3 months, the parameters of the contactor should be tested again before use.
3)
When the altitude exceeds 2000m, it should be used with reduced capacity according to the requirements of IEC 60947-1.

八、 Others
1. Please avoid foreign bodies, grease or corrosive liquids in the terminal, otherwise it will lead to abnormal heating at contact terminals.
2. Please avoid installation in strong magnetic field (around the transformers, the magnet) and the heating objects nearby.
3. In order to prevent loosening, please use the washer when installing the relay. Please use the M5 screws to install relay, screw locking torque within 3 N·m～4N·m; Damage may occur when it is beyond the range.
4. Please pay attention to the thickness of copper bars and the value of the torque. If it goes beyond the recommended values in the below table , it will cause thread slide or installation is not tight. To avoid short circuit or fire,it’s not suggest fix two copper bus bar at same side.

Screw on the load terminal	Recommended thickness of copper bus bar	Recommended hole dimension of copper bus bar	Recommended Flatness of copper bus bar	Torque
M6	2～3mm	Ф6.0mm～ Ф6.5 mm	0.1	6N·m～8N·m

5. The rating load of contact is resistive load. Please assure the surge absorption device together with inductive load when using the L/R≥1 ms inductive load (L Load),otherwise it may lead to the decrease of electrical endurance and defective switch.
6. The relay contacts are sealed and filled with gas. When the contact temperature changes, there is internal gas penetrating characteristic.Neputune relays are forbidden to be used at the temperature beyond our suggestion -40 ℃～85 ℃ for long time.
7. In principle, please do not use it when the relay has fallen down.
8. Neptune products are all RoHS2.0 compliant.
9. Neptune reserves the right to change the product. Customers should confirm the version of the specification before purchasing the product.
10. Please contact Neptune Electric (Kunshan) Co., Ltd for more information or support.